Furnace & heating
AC repair
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterFurnace Repair in Austin, TX
Furnace repair in Austin typically costs between $150 and $650 depending on what’s failed, with most common fixes like ignitor replacements or flame sensor cleanings landing in the $150 to $350 range. Halden Heating and Air Austin gets a written price in your hands before any work starts, so you’ll never watch a tech unload a van wondering what the bill will be. If your furnace is blowing cold air, making strange noises, or cycling on and off every few minutes, call (361) 202-9170 and we’ll get you scheduled with a live arrival time you can track.
This page covers what furnace repair actually involves here in Austin, what it costs, and how our process works from the first call to the final test. For the bigger picture on heating systems, installation, and seasonal maintenance, see our Heating & Furnace page.
When You Need Furnace Repair
Austin winters aren’t brutal, but those cold snaps in December and January are exactly when furnaces decide to quit. Most breakdowns give you warning signs weeks before the system dies completely. Here’s what we hear from homeowners across Austin, from Round Rock to Buda:
- The furnace blows air, but it’s not warm. This usually points to a failed ignitor, a dirty flame sensor, or a gas valve that isn’t opening. The ignitor is the part that glows orange to light the gas. When it cracks, you get room-temperature air blowing through your vents.
- It short cycles. The furnace kicks on for three or four minutes, shuts off, then starts again ten minutes later. In older Austin homes with original ductwork, a clogged filter or an overheating heat exchanger is often the culprit. Short cycling drives up your gas bill and wears out the blower motor faster than anything.
- Banging, rattling, or screeching noises. A screech on startup is typically a worn blower motor belt. A loud bang when the burners light is called delayed ignition, which happens when gas builds up before the flame catches. Neither is something to ignore, especially the banging. That needs a tech.
- The furnace won’t start at all. No power, no fan, no response from the thermostat. Could be a tripped breaker, a blown control board fuse, or a failed transformer. We check the simple stuff first so you’re not paying for a part you didn’t need (and yes, we’ll show you the before-and-after photos to prove it).
- Higher gas bills with no obvious reason. A furnace running at 60% efficiency because of a dirty burner or failing inducer motor will burn more gas to produce the same heat. If your January bill jumped and nothing else changed, your furnace is probably working harder than it should.
One more thing worth saying: if you ever smell rotten eggs or a sulfur smell near your furnace, that’s the odorant added to natural gas. Leave the house, call (361) 202-9170, and we’ll help you get the gas company out to check for a leak before any repair work happens. This is a safety situation, not a service call.
Our Furnace Repair Process
Most furnace repairs in Austin are completed in a single visit, usually 60 to 90 minutes on site. Here’s exactly how a Halden call works, step by step, so you know what to expect before you book:
- Book online or call. You’ll get a real time slot, not a four-hour window. A live person answers the phone 24/7, even at 2 a.m. when your furnace dies on the coldest night of the year.
- Track your tech to the door. You’ll see a live arrival time, the technician’s name, and their photo before they pull up. Our techs are background-checked, uniformed, and drive marked vehicles so you know exactly who’s walking up your driveway.
- Get a written price before work starts. The tech diagnoses the problem, explains it in plain English, and hands you a written quote. You approve it first. No work begins without your sign-off. This is The Relay Standard we hold on every single job.
- We fix it and show you the work. Before-and-after photos document the repair. You’ll see the failed part next to the new one. No mystery, no trust-me-just-pay-the-bill.
- Your 365-Day Done Right Promise kicks in. Every repair comes with a written guarantee. If the same issue comes back inside the coverage window, you get a free second visit automatically. No negotiating, no fine print dance.
Furnace Repair Pricing in Austin
Here’s a straight answer: most furnace repairs in Austin run between $150 and $650. That range covers the part, the labor, and the service call. The spread exists because some failures cost $12 to fix (a flame sensor that needs cleaning) while others involve a $400 control board or a $300 inducer motor.
Here’s what common furnace repairs cost in the Austin market in 2025, based on what we see across Travis County:
| Repair Type | Typical Austin Price Range |
|---|---|
| Flame sensor cleaning or replacement | $120 – $220 |
| Hot surface ignitor replacement | $180 – $320 |
| Blower motor replacement | $400 – $850 |
| Capacitor replacement | $120 – $250 |
| Gas valve replacement | $300 – $600 |
| Thermostat replacement (smart thermostat install) | $150 – $400 |
| Inducer motor or pressure switch replacement | $250 – $550 |
| Control board replacement | $350 – $700 |
What moves the price? Three things. First, the part itself. A Daikin or York ignitor costs more than a generic equivalent, and some Austin homes have high-efficiency furnaces with proprietary parts that run higher. Second, the age of the unit. A 20-year-old Bryant furnace with corroded wiring often needs extra labor to get everything safely connected. Third, the access. Some Austin furnaces live in tight attic spaces where a simple repair takes twice as long.
Every quote includes the full price before we touch a tool. No hourly surprise, no “well, it turns out we needed to…” call after the fact. You’ll know the number up front, and estimates are free. Call (361) 202-9170 to get yours.
If you’re weighing repair against replacement, the math is simple: if the repair costs more than 40% of a new system and your furnace is past 15 years old, replacement usually makes more sense. We’ll tell you that honestly, even when it means a smaller job for us. That’s how we run home.
Furnace Repair vs. Replacement in Austin
Austin homeowners ask this constantly, especially in older neighborhoods like Hyde Park or Crestview where furnaces are pushing 20 years. Here’s the decision framework we use, and we’ll walk you through the same numbers on site:
Repair makes sense when: the furnace is under 12 years old, the part is under $400, and the system has been reliable otherwise. A $200 ignitor on a 9-year-old American Standard? Fix it. You’ll likely get another five or six winters out of it.
Replacement makes more sense when: the heat exchanger has cracked (a safety issue and an expensive repair that often isn’t worth doing on an old unit), the furnace is over 15 years old with a repair quote north of $700, or you’ve had three or more service calls in the last two winters.
We service all major brands including York, Daikin, Bryant, and American Standard, so we can repair or replace whatever you’ve got. We won’t push a replacement when a repair is the right call. The written price you approve decides what happens, not our commission structure.
Same-Day Furnace Repair in Austin
When your furnace fails on a 29-degree night, “next available appointment Thursday” isn’t an answer. We get it. Halden runs same-day calls across Austin whenever our schedule allows, and our 24/7 phone line means you’ll reach a human at midnight, not a voicemail tree.
Here’s what same-day service actually looks like: you call (361) 202-9170, describe the issue, and we give you a real arrival time. Not a window. A time. You’ll track the tech on your phone, exactly like you’d track a rideshare. When they arrive, you get the written price before any work begins. The whole process is built for people who don’t have time to babysit a service call.
FAQs – Furnace Repair
How much does furnace repair cost in Austin?
Furnace repair in Austin typically costs between $150 and $650, with common fixes like ignitor replacements running $180 to $320 and bigger jobs like blower motor or control board replacements landing between $350 and $850. The exact price depends on the part, your furnace’s age, and how accessible the unit is. We provide a written quote before any work starts, so you’ll never face a surprise number. Call (361) 202-9170 for a free estimate.
Can you fix my furnace the same day?
Yes, we offer same-day furnace repair across Austin whenever our schedule allows, and our phone line is answered by a real person 24/7. You’ll get a live arrival time when you book, and you can track your technician to the door in real time. Call (361) 202-9170 to check same-day availability in your neighborhood.
Is it cheaper to repair or replace my furnace?
Repair is cheaper in the short term and usually the right call for furnaces under 12 years old with repair quotes under $400. Replacement makes more sense when your furnace is over 15 years old, the repair quote exceeds 40% of a new system’s cost, or the heat exchanger has failed. We’ll give you an honest recommendation either way, with written pricing to back it up.
Do you service all furnace brands?
Yes, our technicians are certified to service all major brands including York, Daikin, Bryant, American Standard, Carrier, Trane, Lennox, Goodman, and Rheem. We stock common parts on our trucks, which means many repairs get completed the same day without waiting on a supply run. Call (361) 202-9170 to schedule.
Written by Andre Fuller, Owner at Halden Heating and Air Austin, serving Austin.